Автор: charger
Дата: 25-08-05 19:58
Току що ги намерх в нета и затова не е преведено, ,сори.
Е затова трябва да се учат езици
Here is a list of the D30 error codes...
* Err 09: SYSTEM
DESCRIPTION: This error occurs when the EOS D30's self-checking system processing time has
exceeded the specified limit. This error can occur when several switches are pressed at the
same time.
REMEDIAL MEASURE: Because this error is caused by abnormal operation, try releasing the
error by turning the main power switch OFF and then back ON. If this does not solve the
problem, have the EOS D30 examined by a qualified service technician.
* Err 10: SYSTEM
DESCRIPTION: This error occurs if there is an internal malfunction detected during the
camera's self-checking procedure that's executed before every attempted exposure. This is
somewhat similar to the flashing 'BC' warning that occasionally appears on EOS-1 series 35mm
SLRs. Please note that Canon considers Error 10 to be an unusual error that's not supposed
to happen.
REMEDIAL MEASURE: Similar to Error 09, try releasing the error by turning the main power
switch OFF and then back ON. If this does not solve the problem, have the EOS D30 examined
by a qualified service technician. Please be careful to note the conditions under which the
error message occurred.
* Err 22: CF DRIVER
DESCRIPTION: This error occurs when image data cannot be written to the CF card. This error
can occur when the CF card is not fully seated in the camera or if the D30 does not detect a
card-ready signal within a specified time limit or when the CF card is not usable because it
has been corrupted or physically damaged. It can also occur when the camera's battery level
is insufficient to completely write the file to the CF card.
REMEDIAL MEASURE: Use the DC Coupler or recharge the battery first. If the error continues
to occur with sufficient power available to the camera, check that the CF card is properly
inserted. If that's not the problem, then try replacing the CF card. If that does not solve
the problem, have the EOS D30 and one of the CF cards that is causing the problem examined
by a qualified service technician.
* Err 23: NO SPACE LEFT ON CF CARD
DESCRIPTION: This error occurs when the CF card's free space is insufficient for the image
file that has been created. For example, when using a nearly full CF card, if a long
exposure is made with noise reduction shut off, the file size may become larger than
average, resulting in insufficient space to write the file.
REMEDIAL MEASURE: Use a CF card with sufficient free space. If this does not solve the
problem, have the EOS D30 examined by a qualified service technician.
* Err 50: CF FORMAT
DESCRIPTION: This error occurs when the CF card cannot be formatted in the camera.
REMEDIAL MEASURE: Replace the CF card. If this does not solve the problem, have the EOS D30
examined by a qualified service technician.
* Err 51: PLAY MODE
DESCRIPTION: This error occurs when the images stored on the CF card cannot be played back
in the camera.
REMEDIAL MEASURE: Replace the CF card. If this does not solve the problem, have the EOS D30
examined by a qualified service technician.
* Err 80: SHUTTER
DESCRIPTION: This error occurs in the following conditions:
1. When the EOS D30's self-check system detects that the shutter has not been fully charged
(ready to shoot).
2. When the EOS D30's self-check system detects that the shutter operation sequence has not
been completed correctly.
3. When the built-in flash cannot be recharged after the E-TTL preflash but before the main
exposure.
REMEDIAL MEASURE: Try clearing the error by turning the main power switch OFF and then back
ON. If this does not solve the problem, have the EOS D30 examined by a qualified service
technician.
* Err 81: MIRROR
DESCRIPTION: This error occurs in the following conditions:
1. When the EOS D30's shutter release is pressed to the halfway position and the mirror-down
status cannot be verified by the EOS D30's self-checking system.
2. When mirror up/down status cannot be detected during shutter release.
REMEDIAL MEASURE: Have the EOS D30 examined by a qualified service technician.
* Err 82: STROBE
DESCRIPTION: This error occurs when the built-in flash cannot be charged.
REMEDIAL MEASURE: Try clearing the error by turning the main power switch OFF and then back
ON. If this does not solve the problem, have the EOS D30 examined by a qualified service
technician.
* Err 83: POP UP
DESCRIPTION: This error occurs when the built-in flash pop-up operation cannot be detected
even after the pop-up operations have been repeated three times.
REMEDIAL MEASURE: Try clearing the error by turning the main power switch OFF and then back
ON. If this does not solve the problem, have the EOS D30 examined by a qualified service
technician. (NOTE: The EOS D30 can be used with an EX-series Speedlite and/or with an
electronic flash connected through the PC socket even when the built-in flash is
unavailable.)
* Err 84: LENS COMMUNICATION
DESCRIPTION: This error occurs in the following conditions:
1. When electronic communication with the lens cannot be established, after the EOS D30 is
powered ON or when the shutter button is pressed halfway.
2. When the lens diaphragm cannot be controlled during shutter release.
REMEDIAL MEASURE: Clean the electronic contacts on the lens with a clean, soft, dry cloth
and check the mount interface switch on the body's lens mount for dirt or other damage. If
this does not solve the problem, try another Canon EF lens or have the EOS D30 examined by a
qualified service technician.
* Err 86: SYSTEM
DESCRIPTION: This error is a general (i.e., non-specific) data communication error that can
occur when the camera goes through it's self-checking routine prior to every exposure. This
error seems to occur only when battery levels are very low.
REMEDIAL MEASURE: If you are getting this error code consistently with freshly charged
batteries, you should have your D30 checked by Canon Factory Service.
|
|